As one of the important tools in horizontal cable management and the assist of fiber panel, the horizontal cable manager has been warmly welcomed by the public since its debut. The horizontal cable manager comes in varied types such as brush strip cable manager, finger duct cable manager. And the height of it may vary as the network system demands. The fantastic design horizontal cable manager with finger duct is what we will talk about today.
Horizontal Cable Manager with Finger Duct Overview
The FS.COM finger duct horizontal cable manager is designed with flexible fingers, rear pass-through holes and a removable cover. It can be mounted to standard 19 and server rack and cabinet providing well-organized cabling quickly and easily. 1U and 2U versions are both available at FS.COM. Unique hinge cover allows for easy cable moves,adds and changes to connections, saving time and money. The soft and durable finger ducts offer proper bend radius and flexible operation of cable management. 2U version increases more space for Ethernet cable runs.The two holes on the main plate allow for front-to-back or back-to-front cable runs. The finger ducts can be used for both upside and downside cable management. Simplify network maintenance and cost, as well as support future growth and cabling demands.
How the Finger Duct Horizontal Cable Manager Works?
Take 1U finger duct horizontal cable manager as an example, it can be mounted above or below the fiber optic patch panel, with the hinge cover side facing towards us. Open the cover and 12 gaps between 11 finger ducts. The cable is inserted into the above patch panel, and then 2 cables share a same gap. The left 6 couples of cables are all combed to the left vertical cable manager, and the right 6 to the right horizontal cable manager. The two holes on the back of the cable manager are designed for the cables inserted to the below patch panel. The procedure is all the same with the front cabling.With all the cables in their position, you can load the cover.
Vertical and Horizontal Cable Manager
Vertical cable manager is standing vertically on both sides of the cabinet, while the horizontal one is mounted in the cabinet. In addition, whatever the height of the cabinet is, the vertical cable manager can satisfy your needs by mounted with each other. You can choose them according to your actual needs. However, the combination of them shown in the video is no doubt the optimum option. The more detailed information of the two cable managers：Horizontal and Vertical Cable Management At a Glance
This cable manager with finger duct is an optimum option for your horizontal cable management. Get it to protect your equipment, improve the appearance and accessibility of your rack. I am sure you will be content on its hassle-free compatibility with your rack. Any question or puzzle is expected to be asked immediately. With your recommendations, we can go further and grow faster. And also, we sincerely hope that with our products and service, you can gain in both work and life.
Patch panel is defined as the interface between multiple optical fibers and optical equipment. It’s a termination unit that helps networking and fiber distribution from wiring closet to various terminal equipment. Fiber optic patch panel is a mounted hardware unit containing an assembly of port locations in a communication or other electronic or electrical system. Fiber optic patch panel is used to terminate the fiber optic cable and provide access to the cable’s individual fibers for cross connection. They are mostly mounted in 19 inch relay racks, but they can also be mounted on freestanding rails, in cabinets and also on walls.
Fiber Optic Patch Panel Types
Fiber optic atch panel are divided into two types based on different designs, the wall mount and rack mount category. Both types can house, organize, and protect fiber optic cable and connectors. Rack mount patch panels come in flat and angled versions while the wall mount patch panel is used for direct termination of several fibers, and are mostly equipped with routing guides to limit the bend radius for enhanced strain-relief control. They can also be classified according to the count of ports. The common patch panels are come in 12 ports, 24 ports, 48 ports and 96 ports. The height of it can also vary as 1U, 2U, 3U and so on. For more about the types, click here.
How to Connect Fiber Optic Cable To Fiber Patch Panel
Insert the adapters into the mounting plate, then fix the mounting plate in position. Prepare cables based on standard termination procedures and ensure there is enough surplus cable to work with. Connect the cable by fixing the gland and roll the excess fiber onto the spool. After that, remove the protection cap and insert into position in the adapter. Once the cables are all attached, it’s better to use a zip tie to secure the cables in a bundle. In a typical setup, the connection consists of a shorter cable plugged into the front side of the patch panel and a longer cable plugged into the back. In this way, the panel can take the place of otherwise expensive switching equipment. This is the extract from How to Connect Fiber Optic Cable to Fiber Optic Patch Panel. You can find more useful information in it.
How To Use A Fiber Optic Patch Panel
Getting a fiber optic patch panel is mainly for two reasons: termination and better cable management. As for patch panel termination, it is the step to terminate fibers on the patch panel, a precise task required much attention. As for cable management, here I recommend you to accompany it with cable managers. From a top-down perspective, the order of the devices in a cabinet should be: fiber patch panel 1, cable manager 1, fiber patch panel 2, cable manager 2 For fiber optic cabling cable management, you should plan the location of your fiber connectivity hardware carefully, including fiber patch panels. You can choose between direct cross connection and patch panel. It is also necessary to arrange your routing and dressing of your fiber patch cords if you choose to use fiber panels. In the meantime, you also have a choice to use fiber cable management brackets to avoid the dangling fiber patch cables. Owning a fiber optic path will not only spare you a lot of time and energy in cabling design, but also present you a neat cabling system, which will bring you efficient work.
It seems that we have already known that the fiber patch panel is the bridge of fiber patch cables. Fiber patch panel, also known as fiber distribution panel, serves as a convenient place to terminate all the fiber optic cable running from different rooms into the wiring closet and provides connection access to the cable’s individual fibers. Fiber patch panels are termination units, which are designed with a secure, organized chamber for housing connectors and splice units.
How Does Patch Panel Termination Units Works?
We know that there are two major termination solutions for fiber cable: field terminated and pre-terminated. The pre-termination, with most devices terminated by the manufacturers in advance, requires less efforts when installing than field termination does. Therefore, this post is going to offer a glimpse into the field termination which describes the termination of the fiber optic cable in the field or the termination after installation.
Fiber Patch Panel Termination Procedure
In the termination process, the fiber optic cable need to be pulled between two points, then connectors will need to be attached and then connected to a patch panel. In addition, before they can be attached to a panel, connectors need to be attached to each individual strand, and a variety of tools will be needed. With field termination, we can determine the cable length accordingly, and fiber optic bulk cable is very easily to pull from either end of the installation circuit. To carry out the termination, such tools are needed as fiber optic enclosure, fiber cable, patch panel, cable ties, connector panels, permanent marker, fiber optic stripper, cleaver, metric ruler and rubbing alcohol.
To terminate the cable, first slide the boot onto the fiber. Strip the fiber to at least about an inch and a half . Place a mark at 15.5 mm for ST and SC connectors or at 11.5 mm for LC connectors. Clean the stripped fiber with an alcohol wipe and remove any debris. Set the stripped fiber into the cleave and cleave it. Insert the cleaved fiber into the rear of the connector until the mark align with the back of the connector body. Slight the boot up and over the rear of the connector body. After the termination, transmission testing of assemblies need to be performed.
In the final fiber patch panel termination, first, open the front and rear door of the patch panel, and remove the covers. Remover the inter stain relief bracket. Second, use cable ties to put the cables on the bracket. The fibers should be put inside the clips on the tray to segregate the fibers from A and B slots. Put the patch panel into the panels clips. Take the excess fiber slack into the slack management clips. Make a bend in the fiber to maintain slight pressure on the connection.
Conclusion
The processes in the device connection and cable management are linking with each other that missing any or failure in any one will result in the imperfect system, or even the damage. If we own a fiber patch panel, we should make full use of its termination function. The products provided by FS,COM enable you to perfect your cabling system.
When the fiber patch panel is loaded with cables, your cabling is almost finished with the core elements all ready. You can achieve fast and smooth Ethernet connectivity. But turning around, you may find a mess caused and left by the installation. The slack cables without careful comb are hung casually, resulting in a sloppy look just like the noddles being stirred. If we have a look at an expert, it is common to find that they all manage their cables in a good order. And today, we will reveal the secret of the marvelous layout — horizontal and vertical cable management.
Horizontal and Vertical Cable Management
When you try to simulate others’ cabling system, you will inevitably find that the cable management comes in two varieties, horizontal and vertical. When installing cables in a fiber enclosure, you will undoubtedly have to run them both vertically and horizontally. The best solution for this cabling is to run all the cables horizontally from the server directly to the vertical cable management rack. With these two solutions, you can gain many benefits like enhanced availability through reduced downtime, and improved system performance through reduced crosstalk and interference. We all know that crosstalk is harmful and will damage more or less the data transmission. What’s more, it enables us easier and safer access to individual components so as to achieve improved maintenance and serviceability. And the moves, adds and changes will be simplified.
Horizontal and Vertical Cable Manager
With horizontal cable managers, the cables from equipment in racks can be routed neatly and properly and away from damage. If you are using flat-faced patch panels or network switches form which cables come above or below, horizontal cable manager will complete the support pathway for patch cords between the cabling section and the exact connection point (port) on the patch panel or switch. Alternately, horizontal management can be used to create rack-to-rack pathways for patch cords. The FS.COM finger duct horizontal cable manager is designed with flexible fingers, rear pass-through holes and a removable cover. It can be mounted to standard 19 and server racks and cabinets providing well-organized cabling quickly and easily. 1U and 2U versions are both available at FS.COM.
Vertical cable manager just as seen in the below image, utilizes the additional space at the both sides of the cabinet to manage the slack from patch cords, and make sure that they can easily route the largest cable diameter in your plan. For static environments, you can consider installing another vertical cable manager behind the racks, which does not block access to components in the space between the racks. Vertical racks can be also installed under a desk or against a wall and accommodate networking equipment up to 4 RU. Its dual sided fingers enable both front and back well-organized cabling.
Conclusion
With horizontal and/or vertical cable managers, the human errors which may be committed previously due to the confusion of a mess of cables can be easily prevented in horizontal and vertical cable management. Once you have to deal with fiber and copper cables at the same time, apart from our multimedia modular panel, FS.COM cable managers can be used to house and organize fiber and copper cabling while keeping separation between the two.
Some people say that patch panel is a waste, and only a network switch matters. Others, however, hold firmly that patch panel is a significant gadget without which you can hardly imagine how the network cabling will look like. As far as I am concerned, we should view it accordingly.
Why We Should Use Patch Panel?
Apart from the easier cable management it provides, its function resembles the railroad switch. And let’s compare the cables to rails to see how it works. With a railroad switch(patch panel), the train(data) can travel from A to B, C and even more destinations, otherwise it can only go from A to B, or C to D. This article, What Is a Patch Panel Used for?, has explained it thoroughly. In addition, FS.COM offers extensive selection of patch panels.
How to Connect Patch Panel to Switch?
Having made clear of the function of patch panel and the switch, let’s see together how do they connect in the network cabling in case of mistakes in the layout process. Assume that we have a two 24 port feed through patch panels and two 24 port switch, and all the devices mentioned below. We don’t take the punch down panel here is because it has to be punched down first then to connect the cabling system. If you use a punch down patch panel, the methods and procedures to punch down it have been listed in my previous article—How to Punch Down Cat6 into Patch Panel.
Step 1
Find a cabinet large enough to accommodate both the patch panel and switch. And mount the 24 port patch panels and switches all in the same rack. The order from the top to the bottom is like this, patch panel 1, spacer, switch 1, patch panel 2, spacer and switch 2.And prepare the cables in a proper length.
Step 2
Prepare the cable in a proper length to avoid the mess.
Step 3
Use the top 12 ports on the patch panel for the bottom 12 ports on the switch, and the bottom 12 on the patch panel for the top 12 ports on the switch. The one set of patch cables would be just a bit shorter than the other 12.
Step 4
Connect the modulars on the rear side of the patch panel with the cables that go to each unit or room.
OK, congratulation. Now you have a very neat and beautiful cabling system. When powering on, the whole system will work orderly in their own places.
Conclusion
All in all, a patch panel is more of an extension of your Ethernet cables. It's used for the purpose of neatness and the achievement of data crossover. A switch connects your devices into a network allowing them to communicate and share files with each other. To help you better understand the ways to connect the two, we are planning to produce a video to illustrate the steps in details. You can refer to FS.COM for more information and follow us for the further knowledge.
عضو شوید
عضویت سریع
آمار مطالب
آمار بازدید
